overclocking is failed and the system is restored to the defaults setting.

I got my new computer up again and then even updated my BIOS, but since I always get when you start the following message:

Warning! The previous performance of overclocking is failed and the system is restored to the defaults setting.

The hardware I have, according to EVEREST:

Quote:

---

Motherboard:
CPU Type AMD Athlon 64, 2200 MHz (11 x 200) 3500 +
Motherboard Name MSI K8N Diamond (MS-7100) (3 PCI, 2 PCI-E x16, 4 DDR DIMM, Audio, Dual Gigabit LAN, IEEE-1394)
Motherboard Chipset nVIDIA nForce4 SLI, AMD Hammer
RAM 2048 MB (PC3200 DDR SDRAM)
BIOS Type Award (10/27/08)
Ports (COM & LPT) Communications port (COM1)
Ports (COM & LPT) Printer Port (LPT1)

Display:
Graphics Card RADEON X850 Series - Secondary (256 MB)
Graphics Card RADEON X850 Series (256 MB)
3D Accelerator ATI Radeon X850 XT Platinum (R480)
Monitor HP w2207 [22 "LCD] (CZD729043T)

Multimedia:
Sound Card Creative Audigy 2 ZS (SB0350) Sound Card

Motherboard Features:
Motherboard ID 10/27/2008-MS-7100-6A61FM4BC-00
Motherboard Name MSI K8N Diamond (MS-7100)

Front Side Bus Properties:
Bus AMD Hammer
Actual clock 200 MHz
Effective Clock 200 MHz
HyperTransport Clock 1000 MHz

Memory features:
Dual DDR SDRAM Bus
128-bit bus width
DRAM: FSB ratio CPU/14
Actual Clock 158 MHz (DDR)
Effective Clock 316 MHz
Bandwidth 5052 MB / s

Motherboard Technical Information:
CPU Sockets / Slots 1 Socket 939
Expansion Slots 3 PCI, 2 PCI-E x16
RAM Slots 4 DDR DIMM
Integrated Devices Audio, Dual Gigabit LAN, IEEE-1394
Housing (Form Factor) ATX
Motherboard Size 240 mm x 300 mm
Motherboard Chipset nForce4-SLI
Specialties Corecell, Dynamic Overclocking Technology, SATA II, RAID

4 times
[DIMM1: Corsair Value Select VS512MB400]

RAM Features:
Module Name Corsair Value Select VS512MB400
Serial No
Module size 512 MB (2 ranks, 4 banks)
Modulart Unbuffered
Speicherart DDR SDRAM
Memory Speed PC3200 (200 MHz)
Module Width 64 bit
Module Voltage SSTL 2.5
No error correction method
Refresher Rate Reduced (7.8 us), Self-Refresh

Memory Timings:
@ 200 MHz 2.5-3-3-8 (CL-RCD-RP-RAS) / 11-14-2 (RC-RFC-RRD)

Memory Module Features:
Early RAS # Precharge Not Supported
Auto-Precharge Not Supported
Precharge All Not Supported
Write1/Read Burst Not Supported
Buffered Address / Control Inputs Not Supported
Registered Address / Control Inputs Not Supported
On-Card PLL (Clock) Not Supported
Buffered inputs DQMB Not supported
Registered DQMB Inputs Not Supported
Differential Clock Input Supported
Redundant Row Address Not Supported

Memory Module Manufacturer:
Company Name Corsair Memory, Inc.

---

Product http://www.corsairmemory.com/products/xms_home.aspx


Would be nice if you could help me, thank yo

Before Bios update always download the bios defaults and save (F10?)
yes that would make not change when the update was already done.
but:
after Bios update always download the bios defaults and save.

Quote:

---

and the system is restored to the defaults setting.

---

So go into the bios, load defaults, nothing else move, save, reboot.

yes thank you. Have I done and it seems to go well.

Can I do the settings not perhaps a little tune, without damaging the components? Is it feasible or determined?

yes, you can clear up right now or even over clock, etc.
However, you should employ in order to rest and watch what details you on the web and find multiple threads. A recruitment assistance only for you, over your whole bios you will get from any user.

I do not even know your boards. But socket 939 overclocking, or so, because you can find instructions on the Web