Printable View
Is this ram superior for my motherboard I cannot seem to plummet the timings what so ever, even with 2.5v @800MHz stock. Is there a method I be able to gain additional presentation from this ram. My CPU is max out I blend stress 10hours temps staying at 68c on the hottest core it hit 70 on the 8k test but subsequent to that did not go on top of 69c. Does anyone suggest me several memory that that work most excellent with my mobo 4 GB please.
Yes it is at 5-5-5-18 2t showed in the CPUs several proposition you believe over clocking the MHz might create a dissimilarity. By no means heard of CMX2, but you have 2x2GB of Corsair XMS2 DDR2-800 rated for 5-5-5-18-2T @ 1.8V, and you encompass them sitting at 800MHz 4-4-4-12-22-2T @ 2.0V no difficulty. You have got a two of a type of those, and they ran at 4-4-4-12 2T simple at 2.1.
Do not over volt those. They are supposed to max out approximately 2.0v. The over volting determine to decrease their presentation. Misprint you have those similar ones but you cannot drop timings well you have tried to merely drop the 1 timing at a time similar to you determine to try 5-5-5-17 then 5-5-5-16 then 15 but you calculate get to 5-5-5-12 your system determine to reboot to its stock settings and you had it a 2.3v or do you recommend an additional method you be supposed to try to drop your timings or perhaps your mobo presently does not similar to the your ram.
Have you work Memtest to regulate out a couple of bad sticks. It noises extremely odd. They are supposed to not over clock that badly. How do you run memtest on your setup. I have not try that yet I try Prime/blend and Intel burn test in addition it seems that I got to 900mhz but your timings have to be 5-6-6-20 2t 2.1v several higher and your timings have to be 5-7-7-24 2t. It be supposed to not take additional. On the other hand I would recommend checking your spam filter or Junk folder in your email client to be confident.
The CPU-Z (an additional reporting software) reported the XMS2 Corsair 2*2GB DDR2 1066MHZ memory I encompass as 800MHz. Is it for the reason that the reporting software is not updated or be supposed to me set impressive in the BIOS. I utilize Gigabyte GAMA790X-UD4P-AM2+ AMD board with Phenom II 720 T.C. AM3 CPU. That is standard the modules SPD has to be set to impressive the MB determine to post at with defaulting voltage and the tested settings would necessitate to be physically set and you CPU would have to hold up DDr1066 or be over clocked.
I attached the representation of CPU-Z. The holdup center of the seller told me to modify into 5-5-5-5-15, with 2.1V. This results with no boot at the entire I cleared CMOS, misrepresented to Ganged - and this is what be able to be seen in the pic attached. The BIOS is reporting 800MHz at POST stage (previous to XP boots). The CPU and MB be able to hold up 1066. You determine to necessitate to physically setting the memory speed in your BIOS. You have to refer to the BIOS segment of your physical.
The difficulty is that I have 3 parameters: the CPU (AM3 Phenom II), MB (Gigabyte GA-MA790X-UD4P) and 2 memory stick (XMS2 Corsair 2*2GB DDR2 1066 MHZ). The physical does not articulate how to amalgamate. What parameters be supposed to I modify in the BIOS in order to create this memory run at 1066 and how determine to I be familiar with that it runs at this speed. If your physical is not clear on how to adjust the memory regularity, then you have to contact Gigabyte. They hide some of their additional advanced BIOS alternative and they be supposed to be capable to clarify to you how to resolve this. Once you set your BIOS correctly, boot to the OS and run the most recent version of CPU-Z. Look at the memory tab and you be supposed to observe 533 MHz.