open terminal & type
lsusb
now u will get the following output
owais@owais-desktop:~$ lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 0421:0445 Nokia Mobile Phones
Bus 001 Device 002: ID 046d:092f Logitech, Inc.
Bus 001 Device 001: ID 0000:0000
owais@owais-desktop:~$
it is on my compter,ur will not be exactly the same…
Now note the line in which NOkia Mobile Phones is written…it has two number one is 0421 & other is 0445…we’ll take these numbers as 0×421 & 0×445
0421 is the Vendor ID & 0445 is the Product ID
Now enter this comand.
sudo /sbin/modprobe usbserial vendor=0x(vid) product=0x(pid)
eg, in my case::: sudo /sbin/modprobe usbserial vendor=0×421 product=0×445
Now enter this command
wvdialconf create
u’ll get a long output which will be like
Scanning your serial ports for a modem.
Port Scan: S0 S1 S2 S3
WvModem: Cannot get information for serial port.
ttyACM0: ATQ0 V1 E1 — OK
ttyACM0: ATQ0 V1 E1 Z — OK
ttyACM0: ATQ0 V1 E1 S0=0 — OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 — OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 — OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
ttyACM0: Modem Identifier: ATI — Nokia
ttyACM0: Speed 4800: AT — OK
ttyACM0: Speed 9600: AT — OK
ttyACM0: Speed 19200: AT — OK
ttyACM0: Speed 38400: AT — OK
ttyACM0: Speed 57600: AT — OK
ttyACM0: Speed 115200: AT — OK
ttyACM0: Speed 230400: AT — OK
ttyACM0: Speed 460800: AT — OK
ttyACM0: Max speed is 460800; that should be safe.
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
Found an USB modem on /dev/ttyACM0.
Modem configuration written to create.
ttyACM0: Speed 460800; init “ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0″
NOw.. notice the output says that there is a modem at /dev/ttyACM0 & max speed is 460800
now enter this command
sudo gedit /etc/wvdial.conf
A file will open in text editor…now delete everything in that file & paste the following there
[Dialer Defaults]
Modem = Your Modem Name(eg, /dev/ttyACM0 in my case)
Baud = ur max speed(460800 in my case)
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem
Phone = *99#
Username = username
Password = password
Stupid Mode = 1
save the file & you are done
NOw whenevr u need to connect…open terminal & type wvdial,,wait till some sort of IP adress is displayed like
pppd: �[06][06][08]` [06][08]
primary DNS address 218.248.240.135
pppd: �[06][06][08]` [06][08]
secondary DNS address 218.248.240.79
pppd: �[06][06][08]` [06][08]
Now you are connected….hit ctrl+c to dissconnect…
Bookmarks