GA-X58A-UD3R need help to get to 4.0 or 4.2GHz

[Talishh]

I have Intel i7 920 with a GA-X58A-UD3R and Corsair 1600 3x2GB. I was capable to obtain 3.8Ghz actually with no trouble however I haven't be capable to catch to 4.0 or 4.2GHz. Temps are all right, characteristically 62-64 degree C Maximum beneath 100% load Prime95. On one occasion I go to CPU ratio of 20 or 21 the machine will freeze on Prime95 every now and then follow by a BSOD. I see a post at this point discussing regarding altering the Load-line Calibration and the Dynamics Vcore.Any suggestion where to go next would be appreciated. Thank you in advance.

[lorenz]

My stable 4Ghz settings are listed below:

Advanced CPU Features:
CPU Clock Ratio :19
Intel(R) Turbo Boost Tech : Disable
CPU Cores Enabled : All
CPU Multi Threading : Enable
CPU Enhanced Halt (C1E) : Disable
C3/C6/C7 State Support : Disable
CPU Thermal Monitor : Enable
CPU EIST Function : Disable

Standard Clock Control:
Base Clock (BCLK) Control : Enable
BCLK Frequency (MHz) : 200
PCI Express Frequency (MHz) :100

Avanced Clock Control:
CPU Clock Drive :800
PCI Express Clock Drive :900

Advanced DRAM Features:
Performance Enhance : Standard
Extreme Memory Profile (X.M.P) : Disable
System Memory Multiplier (SPD) : 8
DRAM Timing Selectable (SPD) : Quick

Advanced Voltage Control:

Load Line Calibration : Standard
CPU Vcore :1.275
QPI/VTT Voltage 1.150v :1.295
CPU PLL 1.800v :1.80
remaining AUTO

DRAM
DRAM Voltage 1.500v :1.64
DRAM Termination 0.750v: AUTO
remaining all set to AUTO

[Victorious]

I also looking for overclocking help and just reading this post I just want to know how that Gigabyte board performs.i have tried the setting mentioned above to get 4GHz overclocking.But with the setting mentioned above I am also getting 3.86GHz and my temperatures reaches up to 90 degree Celsius just after playing game for five minutes. Will this has any effect to my system?

[JAMES_911]

My Settings used for this board are the same as follows, give these a attempt however I would attempt for 200blk rather not 205blk to start with, don’t put down any voltage on Auto, If you unable to set it manually then keep it set to normal, you will have to provide a number of nb voltage manually although.

Advanced CPU Features:
CPU Clock Ratio : [19 ] 21
Intel(R) Turbo Boost Tech : [Disable] Enabled
CPU Cores Enabled : All
CPU Multi Threading : Enabled
CPU Enhanced Halt (C1E) : Disabled
C3/C6/C7 State Support : Disabled
CPU Thermal Monitor : [Enable] Disabled
CPU EIST Function : Disabled
Virtualization Technology : [Disable] Enabled
Bi-Directional PROCHOT : Enabled

Standard Clock Control:
Base Clock (BCLK) Control : Enabled
BCLK Frequency (MHz) :[200] 205
PCI Express Frequency (MHz) : [100] 101
Advanced Clock Control:
CPU Clock Drive :[800] 700
PCI Express Clock Drive : [900] 700
CPU Clock Skew : 0

Advanced DRAM Features:
Performance Enhance : [Standard] Extreme
Extreme Memory Profile (X.M.P) : Disabled
System Memory Multiplier (SPD) : 8
DRAM Timing Selectable (SPD) : [Quick]

Advanced Voltage Control:
Load Line Calibration : [Standard] Level 1
CPU Vcore :1.275] Normal
Dynamic Vcore Adjust (DVID):[0.000] +0.125
QPI/VTT Voltage 1.150v :[1.295] 1.28
CPU PLL 1.800v :[1.80] 1.84
PCIE 1.500v :[AUTO] Nornal
QPI PLL 1.100v :[AUTO] Nornal
IOH Core 1.100v :[AUTO] 1.26
ICH I/O 1.500v :[AUTO] Nornal
ICH Core 1.1v :[AUTO] Nornal

DRAM
DRAM Voltage 1.500v : [1.64] 1.66v
DRAM Termination 0.750v: [AUTO] 0.83 Half of RAM voltage
Ch-A Data VRef. 0.750v :[AUTO] 0.83
Ch-B Data VRef. 0.750v :[AUTO] 0.83
Ch-C Data VRef. 0.750v :[AUTO] 0.83
Ch-A Address VRef. 0.750v :[AUTO] 0.83
Ch-B Address VRef. 0.750v :[AUTO] 0.83
Ch-C Address VRef. 0.750v :[AUTO] 0.83

[Rivulet]

Hello Guys, I have this similar board X58A-UD3R with the i7 930, except that I'm having problem keeping it cool. I've moved out all the way through above settings for the BIOS, and at a unassuming 3.66 GHz, I'm on 40 idle and 80 load. I'm having a Corsair H50 cooler. If you have any suggestion what should I do to get it cooler please let me know? I'm in suspense to obtain it to 4GHz. I'm using Arctic Silver 5, applied a slim line behind the center of the CPU earlier than putting on the cooler. Any suggestion would be greatly appreciated. Thanks in advance for your help.

[Ceesar]

Tried a mixture of combinations to obtain the heat lesser, as well as the most excellent subsequently far has been adding up two 120mm exhaust fans on the peak of my case as well as spinning downward the Vcore a bit, plus my load temps have go down a small, to 72 C. I have the push setup by means of my Corsair H50 running. Experience similar to I've completed pretty to a great extent each and every one I can actually out-of-the-way from changing the heatsink Going to attempt extra tomorrow in addition to jumble approximately further through BIOS settings.

[Abbie]

Immediate investigation is showing stability for at this moment, 12 hours of MemTest and 10 Hours of Prime and 100 Passes of LinX should cover it. The setting which I used is listed below:

Advanced CPU Features:
CPU Clock Ratio : [19 ] 21
Intel(R) Turbo Boost Tech : [Disable] Enabled
CPU Cores Enabled : [All] All
CPU Multi Threading :[Enable] Enabled
CPU Enhanced Halt (C1E) : [Disable] Disabled
C3/C6/C7 State Support : [Disable] Disabled
CPU Thermal Monitor : [Enable] Disabled
CPU EIST Function : [Disable] Disabled
Virtualization Technology : [Disable] Enabled
Bi-Directional PROCHOT : [Enable] Enabled

Standard Clock Control:
Base Clock (BCLK) Control : [Enable] Enabled
BCLK Frequency (MHz) :[200] 210
PCI Express Frequency (MHz) : [100] 101
C.I.A.2: [-]

Advanced Clock Control:
CPU Clock Drive :[800] 800
PCI Express Clock Drive : [900] 900
CPU Clock Skew : [0] 0
IOH Clock Skew : [0] 0

Advanced DRAM Features:
Performance Enhance : [Standard] Extreme
Extreme Memory Profile (X.M.P) : [Disable] Disabled
System Memory Multiplier (SPD) : [ 8] 8
DRAM Timing Selectable (SPD) : [Quick] [Quick]

Advanced Voltage Control:
CPU Intel Core i7 920 D0 Stepping
Load Line Calibration : [Standard] Level 1
CPU Vcore :[1.275] Normal
Dynamic Vcore Adjust (DVID:[0.000] +0.2125
QPI/VTT Voltage 1.150v :[1.295] 1.34
CPU PLL 1.800v :[1.80] 1.84
PCIE 1.500v :[AUTO] Normal
QPI PLL 1.100v :[AUTO] 1.14v
IOH Core 1.100v :[AUTO] 1.38v (seems to like to stick with my core voltage)
ICH I/O 1.500v :[AUTO] Normal
ICH Core 1.1v :[AUTO] Normal

DRAM
DRAM Voltage 1.500v : [1.64] 1.68v
DRAM Termination 0.750v: [AUTO] 0.84
Ch-A Data VRef. 0.750v :[AUTO] 0.84
Ch-B Data VRef. 0.750v :[AUTO] 0.84
Ch-C Data VRef. 0.750v :[AUTO] 0.84
Ch-A Address VRef. 0.750v :[AUTO] 0.84
Ch-B Address VRef. 0.750v :[AUTO] 0.84
Ch-C Address VRef. 0.750v :[AUTO] 0.84

[Rivulet]

I do not have too much knowledge about overclocking. I am new to Overclock and Bios settings in general. Foremost setting the memory to their suggested maxes light upbeat the cpu and ddr Voltage word of warning leds toward green, which I recognize is insignificant other than lights are good enough, or else is it achievable to run the ram at 1600 through no word of warning lights? My specification are:

Core i7-930
GIGABYTE GA-X58A-UD3R
Crucial Ballistix 12GB (6 x 2GB) PC3-12800 CL8, 1.65V
PNY Nvidia Quadro FX1800
WD CB 1TB Sata 6.0

[desilva]

I try the following settings. It work for about 30minutes of LinX by means of max temps of 79deg followed by BSOD .The only further strange thing so as to was happening was that after power up.
Advanced CPU Features:
CPU Clock Ratio : [19 ] 20
Intel(R) Turbo Boost Tech : [Disable] Enabled
CPU Cores Enabled : [All] All
CPU Multi Threading :[Enable] Enabled
CPU Enhanced Halt (C1E) : [Disable] Disabled
C3/C6/C7 State Support : [Disable] Disabled
CPU Thermal Monitor : [Enable] Enabled
CPU EIST Function : [Disable] Disabled
Virtualization Technology : [Disable] Enabled
Bi-Directional PROCHOT : [Enable] Enabled

Uncore & QPI Features:
QPI Link Speed :[x36] x36 7.38ghz
Uncore Frequency :[x17] x16 3280mhz
Isonchronous Frequency :[Enable] Enabled

Standard Clock Control:
Base Clock (BCLK) Control : [Enable] Enabled
BCLK Frequency (MHz) :[200] 200
PCI Express Frequency (MHz) : [100] 101
C.I.A.2: [-]

Advanced Clock Control:
CPU Clock Drive :[800] 800
PCI Express Clock Drive : [900] 900
CPU Clock Skew : [0] 0
IOH Clock Skew : [0] 0

Advanced DRAM Features:
Performance Enhance : [Standard] Extreme
Extreme Memory Profile (X.M.P) : [Disable] Disabled
System Memory Multiplier (SPD) : [ 8] 8
DRAM Timing Selectable (SPD) : [Quick] [Quick]

Channel A + B + C

Channel A Timing Settings:
CAS Latency Time :[8] 7
tRCD :[8] 7
tRP :[8] 7
tRAS :[24] 24
CR:[2] 2
Advanced Voltage Control:
Load Line Calibration : [Standard] Level 1
CPU Vcore :[1.275] Normal
Dynamic Vcore Adjust (DVID:[0.000]
QPI/VTT Voltage 1.150v :[1.295CPU PLL 1.800v ..............................[1.80] 1.84
PCIE 1.500v :[AUTO] Normal
QPI PLL 1.100v :[AUTO] 1.14v
IOH Core 1.100v :[AUTO] 1.30v
ICH I/O 1.500v :[AUTO] Normal
ICH Core 1.1v :[AUTO] Normal

DRAM
DRAM Voltage 1.500v : [1.64] 1.60v
DRAM Termination 0.750v: [AUTO] 0.80
Ch-A Data VRef. 0.750v :[AUTO] 0.80
Ch-B Data VRef. 0.750v :[AUTO] 0.80
Ch-C Data VRef. 0.750v :[AUTO] 0.80
Ch-A Address VRef. 0.750v :[AUTO] 0.80
Ch-B Address VRef. 0.750v :[AUTO] 0.80
Ch-C Address VRef. 0.750v :[AUTO] 0.80