Results 1 to 7 of 7

Thread: Antec 1200 Airflow

  1. #1
    Join Date
    Mar 2010
    Posts
    154

    Antec 1200 Airflow

    Hi,
    I have a Antec 1200 CPU cabinet. At first the 750 watt supply voltages is provided which has excellent performance. Very good work from Thermaltake at this level, in collaboration with CWT course. The noise is not excessive and it starts at a very low level. On load, the noise increases a little and the fan becomes somewhat audible although this is limited to a discreet breath of air.I need some more help in better airflow for this case. Does this is needed.

  2. #2
    Join Date
    Nov 2009
    Posts
    866

    Re: Antec 1200 Airflow

    In that I can say that the noise is a little higher but the performance is better than knowing that Corsair heatsink. It does not matter actually. I had got mine a similar case which iis quiet well ventilated. I also mounted a very large base config E6850 to 4GHz and everything else that follows and noise level is quiet a low. The noise and airflow is based on the setup you do in the case.

  3. #3
    Join Date
    Nov 2009
    Posts
    942

    Re: Antec 1200 Airflow

    The range in Hundred Antec corresponds to the range player, so far only one model was present, the Nine Hundred. Antec has released one after two new cases, the Three Hundred and Twelve. First question you should ask yourself why nine, Three and twelve. Well this is number of 5.25-inch bays that includes the front, so much for the explanation. The evolution of the 1200 on paper is certain as it offers 6 fan adjustable from outside, a storage location for the cords, look revisited.

  4. #4
    Join Date
    May 2009
    Posts
    1,191

    Re: Antec 1200 Airflow

    For a test, the processor is clocked at 3680 MHz, 440 x 8.5 to 1.30 volts, the graphics card is passed to 720/1800/1110 MHz instead of 600/1500/1000 MHz. I had added this same case to my system. I had added some additional fans to the case. They are Noctua NF-S12-1200: 1200 rpm, an index of 47 CFM and 17 dB (A) noise. The whole system now works well without any issue.

  5. #5
    Join Date
    Apr 2009
    Posts
    825

    Re: Antec 1200 Airflow

    I had overclocked my system by overclocking tool. I had set ATITool artifact on scan mode. The time for the same was 30 minutes, as usual, the highest values will be retained. The measures will focus on the Twelve Hundred unchanged under the three positions L, M and H. The measures will be redone with a additional fan. The position's of the same is towards the left panel and inside the box.

  6. #6
    Join Date
    Apr 2008
    Posts
    2,347

    Re: Antec 1200 Airflow

    Taking about noise there are two measurements will be made on the front of the box 15 cm and 1 meter, base, under the three positions and with a fan. It is consistent with the general line of the range Hundred. We thus find two plastic rails on both sides of the facade, hiding among the 5.25-inch perforated honeycomb manner. The summit welcomed the connectors front, 2 USB 2.0, 1 E-Sata and 2 audio inputs and outputs, the power button sits on the right, reset the left.

  7. #7
    Join Date
    Oct 2004
    Posts
    1,342

    Re: Antec 1200 Airflow

    The left panel of this case is fixed by two thumbscrews on the back cover. A wide window is present on almost the entire height of the panel, she belt a second window with its center located 120 mm fan. A perforated plate with the same structure that protects the plastic facade. The rear reveals the arrangement of the housing. Far below, the location of food, she obviously is mounted on a backplate. On the periphery of the opening in the box, we note the presence of anti-vibration strips, they compress the backplate.

Similar Threads

  1. Which is better among antec 902 and 1200
    By Indivar in forum Hardware Peripherals
    Replies: 5
    Last Post: 23-12-2010, 11:52 PM
  2. Antec 1200 vs Antec df-85
    By Plokstar in forum Hardware Peripherals
    Replies: 5
    Last Post: 02-11-2010, 01:28 AM
  3. Antec 902 or 1200 in Chennai
    By ajay000222 in forum Hardware Peripherals
    Replies: 7
    Last Post: 26-08-2009, 02:47 PM
  4. ANTEC P182 or ANTEC 1200
    By Luis234 in forum Hardware Peripherals
    Replies: 4
    Last Post: 31-03-2009, 06:24 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,714,127,619.20673 seconds with 17 queries