When I type modprobe usb-storage, says nothing and just goes to another line, so you can write a new command. When I type dmesg, it says a lot, but I just copied the end, where it mentions USB. This is what it says:
Code:
4061.848954] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4061.932266] b44 ssb1:0: eth0: powering down PHY
[ 4061.946023] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4062.999895] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4071.156073] usb 1-1: device not accepting address 2, error -110
[ 4071.156155] usb 1-1: USB disconnect, address 2
[ 4071.156189] scsi 2:0:0:0: Device offlined - not ready after error recovery
[ 4071.268089] usb 1-1: new high speed USB device using ehci_hcd and address 3
[ 4074.480776] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4074.556263] b44 ssb1:0: eth0: powering down PHY
[ 4074.570072] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4074.720105] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4077.208834] wlan0: authenticate with 00:1c:10:31:b8:6e (try 1)
[ 4077.210461] wlan0: authenticated
[ 4077.210794] wlan0: associate with 00:1c:10:31:b8:6e (try 1)
[ 4077.212889] wlan0: RX AssocResp from 00:1c:10:31:b8:6e (capab=0x411 status=0 aid=2)
[ 4077.212897] wlan0: associated
[ 4077.214532] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4086.380100] usb 1-1: device descriptor read/64, error -110
[ 4087.888044] wlan0: no IPv6 routers present
[ 4101.596116] usb 1-1: device descriptor read/64, error -110
[ 4101.812100] usb 1-1: new high speed USB device using ehci_hcd and address 4
[ 4116.924056] usb 1-1: device descriptor read/64, error -110
[ 4132.140067] usb 1-1: device descriptor read/64, error -110
[ 4132.360073] usb 1-1: new high speed USB device using ehci_hcd and address 5
[ 4142.768064] usb 1-1: device not accepting address 5, error -110
[ 4142.880083] usb 1-1: new high speed USB device using ehci_hcd and address 6
[ 4153.288071] usb 1-1: device not accepting address 6, error -110
[ 4153.288108] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 4153.556083] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 4168.668083] usb 2-1: device descriptor read/64, error -110
[ 4183.884082] usb 2-1: device descriptor read/64, error -110
[ 4184.100106] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 4199.212062] usb 2-1: device descriptor read/64, error -110
[ 4214.428091] usb 2-1: device descriptor read/64, error -110
[ 4214.644082] usb 2-1: new full speed USB device using uhci_hcd and address 4
[ 4225.052070] usb 2-1: device not accepting address 4, error -110
[ 4225.164074] usb 2-1: new full speed USB device using uhci_hcd and address 5
[ 4235.572046] usb 2-1: device not accepting address 5, error -110
[ 4235.572084] hub 2-0:1.0: unable to enumerate USB device on port 1
Bookmarks