Results 1 to 9 of 9

Thread: Any input on this Micro ATX build would be greatly appreciated

  1. #1
    Join Date
    Jun 2011
    Posts
    85

    Any input on this Micro ATX build would be greatly appreciated

    Every little item I've perused about Micro ATX declares its a terrific case. It just goes with 3 fans, and this apparatus could be run in a tropical nature. I'm considering requesting several additional fans for the top and the side, which ones do you suggest, if any? I desire to strike an offset between quiet and wind current. I am intriguing in gaming. So what all inputs might as well be finished in it? Require recommendations from every one of you. Moreover I need to settle on Intel Core i7 2600k or i5 2500k. I get any on Intel worker rebate from a clan part, so the cost contrast could be around $50. That aside-is there any explanation NOT to get the 2600k for gaming? I'd would give just about anything to have the top of the line CPU for once, that‘s my prevailing inspiration to run with the 2600k

  2. #2
    Join Date
    May 2008
    Posts
    470

    Re: Any input on this Micro ATX build would be greatly appreciated

    Verify you get rapid fans that you are preferably able to control via PWM (via the motherboard) or via a third-gathering fan controller. You hazard cooking your movie cards generally. Heck you peril cooking them in usual depending on if you try SLI in quite a setup (you're talking 650W of hotness with several GTX580's and the CPU) in an exceptionally modest room. A specific GTX580 or single GTX285 will run just fine off of a much littler PSU. No thought on if the Mugen 3 can fit your case/motherboard, even though in the event that you are able to pull the extents up and get imaginative with your google pursuit aptitudes you might as well get a tough situation of what will/will not fit from different utilizing the same or absolutely comparative estimated heatsinks.

  3. #3
    Join Date
    May 2008
    Posts
    389

    Re: Any input on this Micro ATX build would be greatly appreciated

    GTX 285 is about 160W DC. A lone GTX 580 in addition to a specific GTX 285 could leave just about 80W on a 520W PSU, which is likely not altogether enough. I mean genuinely you're no doubt not heading off to prod both GPUs to their most extreme stack similar to that when in fact playing, but this is still asking a part.

  4. #4
    Join Date
    May 2008
    Posts
    413

    Re: Any input on this Micro ATX build would be greatly appreciated

    With a specific GTX 580 taking 288W most extreme in most scenarios (transients past this are unquestionably conceivable), but as likely as not somewhat less, with a stock-timed GTX 580 and a stock-timed Core i7-2600K and a lone harddisk, a Seasonnic S12 II 430W ought to be fine, even though I don't think any individual could blame you for keeping the Seasonic S12 II 520W given your higher anticipated encompassing temps.

  5. #5
    Join Date
    May 2008
    Posts
    351

    Re: Any input on this Micro ATX build would be greatly appreciated

    A value 430W similar to that Seasonic S12 II could no doubt be fine but sincerely a 480W or the Seasonic S12 II 520W could give you a small more breathing room, particularly if on the off chance that temperatures get much higher than you look for and you begin overclocking past just gentle. Value PSU's similar to the Seasonic S12's are specified to their managing DC yield at 50C so I wouldn't anticipate any situations.

  6. #6
    Join Date
    Feb 2008
    Posts
    324

    Re: Any input on this Micro ATX build would be greatly appreciated

    I quite don't think heat is determined to be a situation. I hold the Define Mini, and its really not that small. There's as a matter of fact great wind stream in the case, and a considerable spot of room. Conceded I don't have a movie card in the case, but the i5 2500 is running just about at encompassing with the stock fans and a Hyper 212+. I have a GTX 570 and an i7 930 running honestly queitly in a Lian Li v351-now THAT is small scale. It's likely 1/3 the size of the Define Mini. My temps are a bit elevated, but well within detail.

  7. #7
    Join Date
    Jan 2009
    Posts
    721

    Re: Any input on this Micro ATX build would be greatly appreciated

    I'll undoubtedly get the 2500k on account of I've perused some people about hyper threading in some older games. Utilize the coin for the film card. I'd moreover get a cheaper motherboard if there was preferable rivalry for that ASUS the second most attractive Z68 MiniATX load up is a Gigabyte that while very nearly part of the cost appears to have a much shittier BIOS and less overclocking limit. I'm contemplating if to recovery coin there, but blatantly, motherboards are something I make a point not to would give just about anything to hold back on.

  8. #8
    Join Date
    Apr 2009
    Posts
    3,974

    Re: Any input on this Micro ATX build would be greatly appreciated

    You need t to analyze the length of the card you are attempting to put in with the real length of the case. I figured out how to get a 10.5" 6950 into my MicroATX Silverstone TJ08, but I have 0.5" of room remaining in the middle of the card and the front fan. You could need to yank out those front HD bayous to get an extended card in there. It's got an opening on the side of the case so you might as well be approve with a non-blower outlined GPU. Link administration might be a pain; the case is more modest than what you may be utilized to so there's not a great deal of room to shunt extended links out of the way. The i5-2500k is a 4 heart CPU. The i7-2600k is a four center eight string CPU. Strings are less advantageous than hearts; most recreations favor full centers when they utilize something greater than one. In the event that its not an immense distinction I'd put it all on the line but I remain skeptical about you'd see much of a departure.

  9. #9
    Join Date
    Aug 2009
    Posts
    922

    Re: Any input on this Micro ATX build would be greatly appreciated

    I figured out how to remove the heatsinkers. The things were not yet reaching the sum total of the chips, so they were worse than useless. I voided the warranty. For the cost of DDR3 I am not ready to endure annoy of turning around this and delaying my manufacture to get offbeat stuff.

Similar Threads

  1. Does iPad Micro SIM is Different Than iPhone 4 Micro SIM
    By Raja Ram in forum Portable Devices
    Replies: 4
    Last Post: 09-02-2011, 10:03 PM
  2. Is it possible to build ASUS P5KPL-CM Motherboard in Micro ATX
    By Ighun55 in forum Motherboard Processor & RAM
    Replies: 3
    Last Post: 19-12-2010, 08:48 AM
  3. New computer which allow to play latest game, help appreciated.
    By Bon-hwa in forum Hardware Peripherals
    Replies: 3
    Last Post: 22-10-2010, 12:08 AM
  4. Blue screen nightmare - help appreciated!
    By Damien25 in forum Windows XP Support
    Replies: 2
    Last Post: 17-03-2007, 10:15 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,639,002,201.85383 seconds with 17 queries