Need help with socket pin replacement

[Lucretia]

I have comprised a 775 socket board by means of 4-5 bent pins in the socket. Additional than it engage my friend. I pulled out my elucidate magnifier and got the twisted pins frequently straightened by means of a couple of sewing needles, additional than they are not faultless. It give the impression of being approximating the processor determine to come down and create contact by means of the pins without shorting additional pins. Additional than I not be able to be 100% certain with the intention of the contact determine to be superior or with the intention of a pin would not extend too far when it's compacted by the processor. Would you endeavor putting a C2D processor in this socket. Is the worst case by means of the intention of it immediately would not run, or with the intention of I possibly determine to fry my processor. If it does not run, are there several reasonable methods to get a innovative socket installed on this board. What do you suggest me here.

[Alexisus]

You have to organize pin: utilize a flat blade screw driver and lever fraction of the socket commencing the dead board. As it fracture away maintains the entire the pieces for they restrain your desirable pins. From a broken piece of socket smoothly pull several pins depending on anywhere the solder broke on the base of the pins, some determine to come out the top easier and additional the bottom. Immediately cruise along take your time. The objective at this point is immediately to get a number of pleasant stock for the project. You determine to drop some and additional determine to flick off the tweezers, so more than a few will to be expected be desirable. Pickup a virgin (unbent) pin in tweezers - grasp it by its top - and utilize the scissors to cut off the solder bulb on its bottom, at the bottom of the "V" on top of it. Place it cautiously to one side. You might necessitate additional if you drop it later additional than you be able to cut them later as you necessitate them. Make a note of do not unfold the pin as the pin/barb combo is utilized here in its entirety .

[Nutty]

You have to prepare the not working pin: Each pin leg is in a separate hole, the similar as the holes you immediately pulled the desirable pins commencing. The pins are completed commencing one piece of metal. They are collapse and the front is the pin and the bring up is the barb holding the pin into the plastic socket hole and in addition it make available the solder leg, which most of them necessitate to cut off at the "V" immediately on top of the solder bulb. Preferably the broken pin be supposed to be broken at its shoulder not at the substructure of the neck underneath the head. This is where they frequently break if they are played by means of in straightening attempts. So if your predicament pin is broken down at the base of the neck, most of them are going to break it the entire in excess of again.

[Terrextre]

Spontaneous the material (innovative) pin, you formerly originate and eliminated solder bulb from, and holding it the similar technique as it requirements to be - place the barb resolutely additional than gently in the gap you immediately generated. If you drop the pin, turn upside down the motherboard on a number of white papers and tap it to recover the pin. If it’s lost (create certain it’s not on your board where it possibly determines to generate a short circuit later) get an additional pin and chop the solder bulb at the bottom of the "V" and utilize with the intention of it. With the innovative pin (and it’s barb) at present behind the old pins barb, pickup the Stanley (or additional brand of break off tip) knife - place it perpendicularly, by means of blade tip connecting the pin and its folded barb and by means of point of knife on the top of the steel fold on the folded side.

[AmdUser]

On one occasion the top of the innovative pins barb is level, utilizing the knife the entire in excess of again, tilt the pin neck to the identical angle as the additional. At present give the impression of being cautiously at the pins head - the idea is to have comprised it nestling into the shoulder of the pin in frontage of it (even though higher), when viewed commencing on top of. Have a superior give the impression of being at the entire the additional pin head locations to become comfortable by means of the exact location desirable. To align your pin head (back and forth), utilizing the neck merely, utilize knife, held by means of blade horizontal alongside the vertical part of the pin, beneath the neck, to push it and its barb back in opposition to the socket pocket's rear wall if desirable - ideally you be supposed to be pushing on the old pin and its barb, so utilizing it here to in addition hold the innovative pin against the rear of the pocket. This is the get in touch by means of point between the two pins which determine to convey the electrical current. Otherwise, if barb is not hard alongside rear pocket wall, the pin head determine to be too far forward.

[Tionontati]

If the top of the cutting remark is hard in opposition to the rear wall of the socket pocket where the pin is positioned and the cutting remark is pressed into the socket till the barb top is level by means of the additional, then this pins head projection, forward, determine to be the similar as the additional. If the head is at present sideways commencing its needed alignment, utilize the knife edge in opposition to the neck, to align it by means of careful pressure - as necessary. The intention here is to position the head, imaginatively, by bending the pin beneath the neck/shoulder. In conclusion, utilize the knife to set the pin head level by means of the additional the entire in excess of again utilizing only the neck as the pressure area. On one occasion the pin head is aligned it be supposed to give the impression of being in line by means of the additional commencing the entire the X, Y and Z.