CATIA software tips

[Barsha]

Hi all,

I will give you a some tip about CATIA engineering software. If you built a several painting a good picture the first six prism, and then rotated with a small triangular resection. First painting columns, and then the upper and lower cylinder bottom edge chamfering, and then stretching out hexagonal excision. Three-dimensional modeling of the naming parts spare parts modeling, the system automatically in their model at the beginning of the tree named for the part, usually Part1, Part2 and so the default form. Each entry in the boot. If you go for Nut several painting
(1) first painting a good six prism, and then rotated with a small triangular resection.
(2) first painting columns, and then the upper and lower cylinder bottom edge chamfering, and then stretching out hexagonal excision.

[Itronix]

I suggest doing modeling three-dimensional parts prior to the system in advance of the model tree by default in the part name changed when the file is saved in the part to use the name, so that not only the name of spare parts to avoid duplication, also facilitate the preservation of parts. In parts of the engineering drawings from time to time like a ф39 ± 0.05 in the tolerancing, CATIA default font SICH can not be required to mark, mark the ф39 0.05 form. Then you can set the tolerance type TOL-1.0 and marked with the α CATIA Symbol font. Check and reply

[SpearMan]

The use of right mouse button in CATIA as following:
(1) In the semi-cutaway view of the size marked holes, the size of line is often half the extension line on one side only there. If you click on the hole contour, according to left to confirm, there is the whole size of line. You can not put the size of pre-click the right mouse button and select "Half Dimension", you can mark out the half the size of line.
(2) mark 2 arc distance between the outer edge, when the mouse to select two arcs, the system automatically captures the distance between the center of the circle into two dimensions, this time without the same size before placing the right-click, the pop-up the menu in the "Extension Lines Anchor", select the desired annotation type.
(3) Engineering diagram is sometimes necessary to mark a slash of the horizontal or vertical distance, or to mark an endpoint of a diagonal line with a distance, when you can select the object to be marked after the right pop-up menu in the Select "Dimension Representation" in the size of the type required. Two linear perspective can also be marked size pop-up menu in the "Angle Sector" select the desired annotation methods.

[XDRoX]

I use CATIA software, the process, had encountered "Part Design" and "Assembly Design" is the image of the original environment of a tool icon in all the English words into a form of expression, such as "chamfer" becomes "ChamferHeader", stretching into "PadHeader" and so on, in using them. Reason could be the use of CATIA in the process, due to operational reasons, resulting in a number of temporary files, such as CAT settings, CAT temp and other documents, these temporary files are automatically saved, may have some impact on the use of CATIA. So, check out these documents should be timely and will delete it. Another solution is to set the "Tools" < "options" in the "reset" for "for all the tab pages". I conduct these operations, the tool bar on the image of the icon changes back to the form. Encounter such problems a friend try.

[ChrisUlrich]

If you want to Engineering drawings in the frame and the title bar of the insert
you need to can be first a variety of drawing the title bar of the size of frame is made templates, respectively, into the various drawings. To do the following: enter the "drafting" status, select the drawing size, to enter "Edit" < "Background", in accordance with the standards required to draw a good frame and title bar, save it. In paintings, a good engineering drawings, go to "File" < "Page setup", the pop-up dialog box, select "Insert Background View", select the corresponding frame format, click on "Insert" can be. You can be in the projection view before making a good frame and insert the title bar. To do the following: the establishment of a good part model environment, click on "File" < "New from", according to the size of projection view of drawings needed to choose well in advance of the frame template files, can be plugged directly into a good frame and the Drafting of the state of the title bar. All the best.