A solution to WGA (KB892130) failure to install

I, like a lot of people with genuine copies of windows, have experienced
problems with installing KB892130. I've been in and out of a lot of posts on
the subject and tried various offered solutions which have (and have not)
worked for some people. After numerous variations, the following has worked
and I'm now able to run the update service as it was intended.

Download psexec.exe from:-

http://www.sysinternals.com/Utilities/PsExec.html

and put the file in root directory (C:\)

Download the WGA update executable from:-

http://www.download.windowsupdate.co...82dcea49a0.exe

and install in C:\temp.

Rename the file in C:\temp to WGA.exe (original file toooooo long)

At DOS command line type:-

psexec -i -s c:\temp\WGA.exe

The above tested and works - for me at least - Hope it works for others

Many thanks for all the inputs that got me to this position - there are too
many to mention by name - I just grateful to the newsgroups

Worked fine for me! Thanks a lot!

It also worked fine for me. Thank you so much.

Seems a good solution.I found that disabling ghost software and altering my
firewall settings cured the problem.Microsoft needs full access to your
computer.
Microsofts' solution of the doing a clean install seems on the face of it
rather stupid.
Terry


"Mike" wrote:

> It also worked fine for me. Thank you so much.
>
>

Thanks so much. I worked on this problem since last night and your fix
works. Of course, some people have to bit a little tech savvy to
understand the dos commands, but it works. My only suggestion is that
when you get to a dos prompt, type c:\ to get to the root where
psexec.exe is located. Also, only choose the psexec.exe file when you
unzip the program because it has many many files. The others are not
needed.

If it wasn't for you, I would be here for days...thanks again.

Thanks so much. I worked on this problem since last night and your fix
works. Of course, some people have to bit a little tech savvy to
understand the dos commands, but it works. My only suggestion is that
when you get to a dos prompt, type c:\ to get to the root where
psexec.exe is located. Also, only choose the psexec.exe file when you
unzip the program because it has many many files. The others are not
needed.

If it wasn't for you, I would be here for days...thanks again.

it worked perfectly, i think everybody must do the same think.many thanks who
find it.

If redirecting is disabled in your IE or by a "security software"
running in the background, here you go:
http://download.microsoft.com/downlo...4/WGADiag2.exe

Download and save the tool, quit your browser, execute the tool and
try to access Windows Update via IE again afterwards.

Bye,
Freudi

The link below worked for me also(xp home edition). I no longer get the
"failed to install" message, but there are apparently no updates for me to
download. The last download I have were on 2/16/06 (6 of them... 2 media
player, 3 security updates, 1 malicious software tool). Have there been any
updates for XP since then that anyone is aware of?

I don't usually have the need to use the message board, and am somewhat of a
novice at it. I hope I'm posting to the right place.

Thanks to all who post here. There are many knowledgable folks out there
who are saavy enough to know how to fix problems, but more importantly, share
them with others who are not as fortunate. I hope I can return the favor
someday.


http://go.microsoft.com/fwlink/?linkid=52012

I have everythign going the first way u said but when i do the comand line it will startup ok with no problems than when it says finish the comand line says:" C:\temp\WGA.exe excited on N-EXW8I2GF3G9NP with error code 0. "
I tried restrating and doing windows update but it still fails.

I have the same experience as Blake. It seems this way out is outdated.

Blake,

My post was over 18months ago . I'm assuming the ececutable is no longer in
location I got it from (?)

"Blake" wrote:

>
> I have everythign going the first way u said but when i do the comand
> line it will startup ok with no problems than when it says finish the
> comand line says:" C:\temp\WGA.exe excited on N-EXW8I2GF3G9NP with
> error code 0. "
> I tried restrating and doing windows update but it still fails.
>
>
> --
> Blake
> ------------------------------------------------------------------------
> Blake's Profile: http://forums.techarena.in/member.php?userid=34929
> View this thread: windows-update/473534.htm
>
> http://forums.techarena.in
>
>

jakro64,

as per respopnse "Blake" - My post was over 18months ago . I'm assuming the
executable is no longer in location I got it from (?)


"jakro64" wrote:

>
> I have the same experience as Blake. It seems this way out is outdated.
>
>
> --
> jakro64
> ------------------------------------------------------------------------
> jakro64's Profile: http://forums.techarena.in/member.php?userid=35280
> View this thread: windows-update/473534.htm
>
> http://forums.techarena.in
>
>

Go to this adress

http://technet.microsoft.com/en-us/s.../bb897553.aspx

And download "PsTools"
It's a ZIP-file with PsExec and some other tools in it!