Results 1 to 5 of 5

Thread: Overclocking Q6600 with best fsb / ram 4GB

  1. #1
    Join Date
    Jan 2009
    Posts
    70

    Overclocking Q6600 with best fsb / ram 4GB

    hi
    i am interested to overclock my Q6600 + ram 4GB for which i need your help so please can any one can help me ? i want to know what is the best fsb rate that i can achieve with 4gb and Q6600 which can give me best out come .Is that possible to get together for the FSB: DRAM 1:1 on it
    thank you

    Asus P5K-E/WiFi-AP
    Intel Core 2 Quad Q6600
    Arctic Cooling Freezer 7 Pro
    PC2-8500 1066MHz EVO ONE Dual Channel

  2. #2
    Join Date
    May 2008
    Posts
    666

    Re: Overclocking Q6600 with best fsb / ram 4GB

    You must need to get FSB 2 times do it for your FSB: DRAM 1:1 on it. With Stock your Q6600 FSB is 266MHz, so you need to push up to 533MHz running to get to 1:1.

  3. #3
    Join Date
    May 2008
    Posts
    656

    Re: Overclocking Q6600 with best fsb / ram 4GB

    What you can do is the multiplier of the Q6600 on 8, or maybe 7 (just try or stable) and then automatically generate a higher FSB if the total (2.4 GHz stock) to retain approximately Try different once a multiplier of 8 with an FSB of 333MHz to start, then run your memory at 667MHz all (PC5300 normally). If that works go a step further eg 7x400 (2.8 GHz) and memory at 800MHz so run (PC6400) or 8x375 (3ghz) and memory at 740Mhz. Be cautious and do not give too much vCore, just do steps vise. Is nice to see your Q6600 to 3ghz stable on to get a lot more from your quad core. I have too, running here at 3555mhz (9x395mhz) and Memory 1:1 (790mhz) 4-4-4-12 timings.

  4. #4
    Join Date
    Dec 2007
    Posts
    1,736

    Re: Overclocking Q6600 with best fsb / ram 4GB

    32 bit Windows can support 4GB of RAM ... BUT, the steering system must support it called PAE (Physical Address Extension) to go over the 3GB (or 3.5 GB, it is shown). Q6600 ram support is good basically cpu and ram relation is different.also The get that the type of memory that you already need more voltage to its max speed factory to get? Try these settings :

    VCore 1.375
    Vddr 2.0
    FSB 400
    Multiplier 6
    Memspeed 800
    Timings on auto
    Vdroop protection you need to set (default is off)
    Cpu spread spectrum off

    Rest you can leave on auto.

  5. #5
    Join Date
    Jan 2006
    Posts
    830

    Re: Overclocking Q6600 with best fsb / ram 4GB

    - Model CPU: Q6600
    - Stepping CPU: L730b341
    - CPU Revision: G0
    - CPU Frequency: 4.05 Ghz
    - Ai Overclock Tuner: [Manual]
    - OC from CPU Level Up [Auto]
    - CPU ration setting: [Manual]
    - Ratio CMOS Setting: [9] <<<missing this line in case of manual
    - FSB frequency: 450
    - FSB strap to North Bridge: 266
    - PCIE frequency: 101
    - DRAM frequency: 1125
    - DRAM command rate: 2T
    - DRAM Timing Control: [Manual]
    - CAS latency: 5
    - RAS to CAS delay: 4
    - RAS precharge: 4
    - RAS Active time: 10
    - Row refrsh cycle time: Autos
    - Write recovery time: Autos
    - Read to precharge time: Autos
    - Read to write delay (S / D): Auto
    - Write to read delay (S): Auto
    - Write to read delay (D): Auto
    - Read to read delay (S): Auto
    - Read to read dealy (D): Auto
    - Write to write delay (S): Auto
    - Write to wrtie delay (D): Auto
    - DRAM Static read control: Disabled
    - Ai clock twister: Moderate
    - Transaction Booster: Disabled
    - Relax level: 0
    - CPU Voltage: 1.495
    - CPU PLL voltage: 1.60
    - North bridge voltage: 1.65
    - DRAM Voltage: 2.26 (reel no bios)
    - FSB termination voltage: 1.57
    - South Bridge Voltage: 1.07
    - Loadline calibration: Enabled
    - CPU GTL Reference: 0.63
    - North Bridge GTL Reference: 0.63
    - A channel DDR2 voltage ref: DDR2_REF
    - DDR2 Channel B ref voltage: DDR2_REF
    - DDR2 controller ref voltage: DDR2_REF
    - SB 1.5 Voltage: 1.55
    - CPU spread spectrum: Disabled
    - PCIE spread spectrum: Disabled
    - CE1 support: Disabled
    - CPU TM function: Disabled
    - Vanderpoll technology: Disabled
    - Execute Disable Bit: Enabled
    - Max CPUID value limit: Disabled

    - Cooling: Water
    - Temperatures IDLE / FULL: 38 ° / 67 °
    - Type of OC: stable

Similar Threads

  1. At what maximum overclocking ghz can a Q6600 cpu run?
    By Rasesh in forum Overclocking & Computer Modification
    Replies: 2
    Last Post: 21-08-2012, 10:52 AM
  2. Overclocking Q6600
    By DANIEL 602 in forum Overclocking & Computer Modification
    Replies: 3
    Last Post: 27-02-2009, 12:31 PM
  3. Problem with overclocking Q6600 has a 3.6GHz
    By DANIEL 602 in forum Overclocking & Computer Modification
    Replies: 3
    Last Post: 19-02-2009, 05:46 PM
  4. Overclocking A Q6600
    By super soaker in forum Overclocking & Computer Modification
    Replies: 3
    Last Post: 08-01-2009, 04:58 PM
  5. Overclocking Q6600 Gb with P45, need some guide.
    By Wouter in forum Overclocking & Computer Modification
    Replies: 1
    Last Post: 02-08-2008, 03:20 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,711,716,014.49218 seconds with 17 queries