Is my CPU compatible with Backtrack 5?

[GaganGang]

I was able to use all previous versions of backtracking on this computer, but when I pit the 32-bit version of KDE to boot from my flash drive and boot, I get an error saying: "This requires a processor core x86-64, but only detected an i1686 CPU unable to boot -. Please use a kernel appropriate for your CPU. “I have an Intel Core Duo T2050. Backtrack 5 how I can run on this computer more? Why do I get this error, but when I run Backtrack 5 from a DVD instead of booting from a flash drive works fine? Backtrack 5 This works perfectly when booting from the DVD. When I try to boot from my flash drive using the same 32-bit image, I get that error I wrote above. Why is this?

[Aleksandra]

I was also facing the exact problem which u facing now. I have spend lot of time in finding the exact problem and finding its solution than one day I figured out its an install error to usb or setting go into to your bios and check the settings. After finding the exact cause I fixed it. I tried much application for this like unetbootin and many more. If anyone facing similar problem than they can reply me here with exact scenario.

[Dolsy_bendal]

partitions are messed up  and deleted  all partitions using fdisk in Linux 
fdisk -l
select your usb xxxx
fdisk /dev/xxxx
press d then 1
press d then 2
press d then 3
press w and enter

windows uses disk manager and delete all partitions on your usb. Format the usb

[Unequaled]

modprobe usb-uhci
modprobe usb-ohci
modprobe usb-storage
run dmesg

dmesg

you show get some output like this

Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdb: 78242976 512-byte hdwr sectors (40060 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 78242976 512-byte hdwr sectors (40060 MB)
sdb: assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: Attached scsi disk sdb
usb-storage: device scan complete

now lets

fdisk -l | grep sdb              (sdb is the output yours might be differnet check the output of dmesg)

output

Disk /dev/sda doesn't contain a valid partition table
Disk /dev/sdb: 40.0 GB, 40060403712 bytes
/dev/sdb1               1        4870    39118243+   c  W95 FAT32 (LBA)
now mount the usb

mount /dev/sdb1 /mnt
note (sdb1)maynot be yours it just an example

then do as above delete the partitions and format

[Wali]

When I type modprobe usb-storage, says nothing and just goes to another line, so you can write a new command. When I type dmesg, it says a lot, but I just copied the end, where it mentions USB. This is what it says:

4061.848954] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4061.932266] b44 ssb1:0: eth0: powering down PHY
[ 4061.946023] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4062.999895] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4071.156073] usb 1-1: device not accepting address 2, error -110
[ 4071.156155] usb 1-1: USB disconnect, address 2
[ 4071.156189] scsi 2:0:0:0: Device offlined - not ready after error recovery
[ 4071.268089] usb 1-1: new high speed USB device using ehci_hcd and address 3
[ 4074.480776] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4074.556263] b44 ssb1:0: eth0: powering down PHY
[ 4074.570072] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4074.720105] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4077.208834] wlan0: authenticate with 00:1c:10:31:b8:6e (try 1)
[ 4077.210461] wlan0: authenticated
[ 4077.210794] wlan0: associate with 00:1c:10:31:b8:6e (try 1)
[ 4077.212889] wlan0: RX AssocResp from 00:1c:10:31:b8:6e (capab=0x411 status=0 aid=2)
[ 4077.212897] wlan0: associated
[ 4077.214532] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4086.380100] usb 1-1: device descriptor read/64, error -110
[ 4087.888044] wlan0: no IPv6 routers present
[ 4101.596116] usb 1-1: device descriptor read/64, error -110
[ 4101.812100] usb 1-1: new high speed USB device using ehci_hcd and address 4
[ 4116.924056] usb 1-1: device descriptor read/64, error -110
[ 4132.140067] usb 1-1: device descriptor read/64, error -110
[ 4132.360073] usb 1-1: new high speed USB device using ehci_hcd and address 5
[ 4142.768064] usb 1-1: device not accepting address 5, error -110
[ 4142.880083] usb 1-1: new high speed USB device using ehci_hcd and address 6
[ 4153.288071] usb 1-1: device not accepting address 6, error -110
[ 4153.288108] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 4153.556083] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 4168.668083] usb 2-1: device descriptor read/64, error -110
[ 4183.884082] usb 2-1: device descriptor read/64, error -110
[ 4184.100106] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 4199.212062] usb 2-1: device descriptor read/64, error -110
[ 4214.428091] usb 2-1: device descriptor read/64, error -110
[ 4214.644082] usb 2-1: new full speed USB device using uhci_hcd and address 4
[ 4225.052070] usb 2-1: device not accepting address 4, error -110
[ 4225.164074] usb 2-1: new full speed USB device using uhci_hcd and address 5
[ 4235.572046] usb 2-1: device not accepting address 5, error -110
[ 4235.572084] hub 2-0:1.0: unable to enumerate USB device on port 1