Results 1 to 4 of 4

Thread: 0F00: 133C Error Code: No suitable disk or media is present

  1. #1
    Join Date
    Nov 2010
    Posts
    13

    0F00: 133C Error Code: No suitable disk or media is present

    Hello to all, I have a trouble and is that occasionally, when I try to start my computer, it unable to load Windows and the system cannot fix it saying that most likely there was a trouble with new hardware or software installed, even though I haven't installed none of the hardware and about software, I just installed the Windows 7 updates. So I presently have the alternative of recovering the system to start my computer. The problem is that not all the time occurs. When it happened a couple of times, I decided to execute the diagnostics and it gives a 0F00: 133C error. And later a 4400: 011A error. Error Code: 0F00:133C msg disk: no suitable disk media is present. Please help me!

  2. #2
    Join Date
    Apr 2009
    Posts
    994

    Re: 0F00: 133C Error Code: No suitable disk or media is present

    I recommend you to update the drivers with the help of the system manufacturer support. It may be that the problem is created suitable due to the defective RAM or Video card. That is the cause I recommend you to update the drivers from the system manufacturers website. Error Code 4400:011A.

  3. #3
    Join Date
    Nov 2009
    Posts
    865

    Re: 0F00: 133C Error Code: No suitable disk or media is present

    Error Code 0F00:133C
    Msg: DISK- No suitable disk media is present.
    This error message is come across when you probably have a bad video card or flaky RAM. Unplug all the peripheral devices such as printers, scanners etc and ensure whether you come across with this error message. Also I would advise you to install the latest drivers for the Video card from the manufacturer website and check for the error. Update a driver for hardware that isn't functioning correctly.

  4. #4
    Join Date
    Apr 2009
    Posts
    1,107

    Re: 0F00: 133C Error Code: No suitable disk or media is present

    I would recommend you to organize Chkdsk to run when the system restarts next time. Perform the steps shown to configure Chkdsk to run when the Windows restarts next time. Click to the Start button on the task bar, after that go to the open option and in that type cmd and then press enter. Make use of any one of the following Procedures:
    Procedure 1: To run Chkdsk into the read-only mode, on the command prompt and in that type chkdsk, and then hit ENTER. Procedure 2: To fix errors through no scanning the volume for bad division, at the command prompt, type chkdsk volume:/f, and then hit ENTER.

Similar Threads

  1. Replies: 8
    Last Post: 09-01-2012, 10:40 PM
  2. Error Code 4400:011A and Error Code 0F00:133C
    By mkwn in forum Operating Systems
    Replies: 1
    Last Post: 14-10-2011, 12:39 PM
  3. Error codes 0f00 0667 & 0f00 0648
    By Virtue in forum Operating Systems
    Replies: 5
    Last Post: 29-09-2010, 07:55 AM
  4. Windows 7 repair disk error code 0x4001100200001012
    By Gafur in forum Operating Systems
    Replies: 5
    Last Post: 15-08-2010, 07:06 PM
  5. Can't write to disk getting error code 50
    By Who is it in forum Operating Systems
    Replies: 6
    Last Post: 28-05-2010, 01:47 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,711,617,852.25041 seconds with 17 queries