Go Back   TechArena Community > Software > Operating Systems
Become a Member!
Forgot your username/password?
Register Tags Active Topics RSS Search Mark Forums Read

Sponsored Links



How to configure Cisco router with telnet?

Operating Systems


Reply
 
Thread Tools Search this Thread
  #1  
Old 25-12-2009
Member
 
Join Date: Nov 2009
Posts: 1,416
How to configure Cisco router with telnet?
  

Hey, I got a problem regarding the setting of the CISCO router. I have recently purchased a CISCO router which is bearing model no. 2600 but the problem is that i don't know how to configure the router with the telnet. So i have raised the question here to get the proper solution of the same. I think this the right place to ask the same. So help me. Any help may be appreciated. Thank you

Reply With Quote
  #2  
Old 25-12-2009
Member
 
Join Date: Jan 2006
Posts: 4,552
Re: How to configure Cisco router with telnet?

Hello, If i am not wrong then this the first step to when you wist to start working with it. This is also notify that you are using the CISCO certified network. So use the below given command to set up the telnet on you CISCO router. The Configuration will help you to set up the same. So go with it and check whether it is working or not
Code:
terminal Configuration
line vty 0 4
password <Enter password>
login
__________________
In The Absence Of Light
Darkness Prevail's
Reply With Quote
  #3  
Old 25-12-2009
Member
 
Join Date: Jan 2006
Posts: 7,131
Re: How to configure Cisco router with telnet?

This document uses the Router-2 configuration.
In order to set up the router to allow Telnet access, issue the line vty command. This command allows for the configuration of Virtual Terminal (VTY) lines for remote console access. You can configure the router to accept one or more Telnet sessions. It is strongly suggested that you configure password checking with the login and password line configuration commands. This example configures the router to accept five sessions, with the password "letmein":

Code:
Router-2(config)#line vty 0 4
Router-2(config-line)#login
% Login disabled on line 66, until 'password' is set
% Login disabled on line 67, until 'password' is set
% Login disabled on line 68, until 'password' is set
% Login disabled on line 69, until 'password' is set
% Login disabled on line 70, until 'password' is set
Router-2(config-line)#password letmein
SOURCE: cisco.com
__________________
"Me fail English!? That unpossible!"
Reply With Quote
  #4  
Old 25-12-2009
Member
 
Join Date: Jan 2006
Posts: 6,899
Re: How to configure Cisco router with telnet?

Hey to configure the same use the folowing step.
  • First connect your CISCO
  • Write enable and then hit the Enter which go to enable mode.
  • Write 'config t' after that press enter key for the configure mode.
  • Write "line vty 0 4" after that enter key to go to the configuration mode.
  • Write "login" after that enter key to configure the router/switch which will enable the password prompt when user login
  • Enter the password you want
  • Write exit
  • Now your configured.
Reply With Quote
Reply

  TechArena Community > Software > Operating Systems
Tags: , , , ,



Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads for: "How to configure Cisco router with telnet?"
Thread Thread Starter Forum Replies Last Post
"Cisco connect" cannot find Cisco Linksys E1200 router $Iain$ Networking & Security 5 25-03-2012 07:41 PM
Cisco 1921 router vs. Cisco 1941 router gMALI Networking & Security 6 22-07-2011 07:29 PM
How to configure EIGRP on cisco 2600 router Krupa Networking & Security 3 08-04-2009 07:05 PM
Unable to telnet Cisco 3560 Switches spec_r Networking & Security 3 25-02-2009 10:36 PM
Problem of Cisco 7920 VoIP phone on Cisco 870 router Wguy2008 Networking & Security 4 30-11-2008 10:35 AM


All times are GMT +5.5. The time now is 01:53 AM.