Go Back   TechArena Community > Technology > Networking & Security
Become a Member!
Forgot your username/password?
Tags Active Topics RSS Search Mark Forums Read

Reply
 
Thread Tools Search this Thread
  #1  
Old 29-12-2011
Member
 
Join Date: Dec 2011
Posts: 25
how can i manually connect to WAN through huawei echolife hg532

HI, as the title implies I wanted to know as how can i manually configured the WAN connection? I am using Manual Dialing method for my PPPoE ADSL connection, with Huawei - EchoLife HG532b Stc Firmware as it is already mentioned in the title.

I would like to make use of Telnet command to connect and disconnect the WAN Connection. Because i believe as it will be further dependable to utilize those commands in Telnet Scription tools, like TST10 than utilizing browser configuration page. any suggestion regarding the same will be appreciated.
Reply With Quote
  #2  
Old 29-12-2011
Member
 
Join Date: Nov 2010
Posts: 442
Re: how can i manually connect to WAN through huawei echolife hg532

I am not sure about the further router settings but still you should make sure as you are login with the ?telnet 192.168.1.1? IP address, because though that you can simply manually configured all the WAN connection. Here you need to provide the ID and the password provided to you, and by using this IP address you can proceed further.
Reply With Quote
  #3  
Old 29-12-2011
Member
 
Join Date: Mar 2011
Posts: 464
Re: how can i manually connect to WAN through huawei echolife hg532

well, i have mentioned the basic setup that i have done and everything works fine with it and thus would suggest you to do the same thing.
First of all you need to access the router via http://192.168.1.1 and input the default username and password. Once you completed with it you have to then click on Basic, then WAN in the left hand menu, and in the window select configured the following mentioned settings.
Code:
VPI = 0
VC = 38
Active = Yes
Mode = Routing
Encapsulation = PPPoA (PPP over ATM)
Multiplex = VC
Username =  as provided by your ISP
Password = *as provided by your ISP
Default Route = Enable
NAT = Enable
Obtain an IP Address Automatically = Green Dot (Enabled)
IP Address, Subnet Mask, Gateway all = 0.0.0.0
Connect on Demand: Max Idle Timeout = No green dot
Nailed-Up Connection = Green dot (Enabled)
TCP MSS for TT = 1392 For BT = 1418
MTU For TT = 1432 For BT = 1458
RIP = Disable
Reply With Quote
  #4  
Old 29-12-2011
Member
 
Join Date: Dec 2011
Posts: 25
Re: how can i manually connect to WAN through huawei echolife hg532

Quote:
I am not sure about the further router settings but still you should make sure as you are login with the ?telnet 192.168.1.1? IP address, because though that you can simply manually configured all the WAN connection. Here you need to provide the ID and the password provided to you, and by using this IP address you can proceed further.
Hey thanks for the suggestion but still the thing is like technical team from stc upgraded my firmware thus i don?t know the newer ID and password through which i could login with this IP address. Please let me know what could be this information, and from where can i get it ?
Reply With Quote
  #5  
Old 29-12-2011
Member
 
Join Date: May 2011
Posts: 459
Re: how can i manually connect to WAN through huawei echolife hg532

that?s quite awful but still can you please let me know which firmware version you have installed so that i could provide you the password and the user name for the same?
Reply With Quote
  #6  
Old 29-12-2011
Member
 
Join Date: May 2011
Posts: 424
Re: how can i manually connect to WAN through huawei echolife hg532

Quote:
that?s quite awful but still can you please let me know which firmware version you have installed so that i could provide you the password and the user name for the same?
I think the above user is completely unaware about this thing because as far as i know until and unless you change the password it remains the same by default no matter which version?s firmware you have installed. Anyways see i have mentioned the information though you can carry on.

IP Address:- 192.168.1.1

Default Username:- admin

Default password:- admin


But let me tell you as the this IP will be dynamic but still of you are expecting Set static IP or for DMZ for your router than you may have to contact your ISP.
Reply With Quote
  #7  
Old 29-12-2011
Member
 
Join Date: May 2011
Posts: 442
Re: how can i manually connect to WAN through huawei echolife hg532

Quote:
Hey thanks for the suggestion but still the thing is like technical team from stc upgraded my firmware thus i don?t know the newer ID and password through which i could login with this IP address. Please let me know what could be this information, and from where can i get it ?
I think it would be better if you simply contact the service center regarding the same and mentioned your firmware version and each and every detail they inquire. Because once you done this they could surely provide you your ID and password, and as you get the password you can simply ask you doubt to them as well regarding manually configuring the WAN connection. Because see this is also depend upon the firmware that you have installed, thus if this feature is available on the installed firmware then obviously you can do that, and be aware as the firmware version changes all the features and option used to get changed.
Reply With Quote
  #8  
Old 29-12-2011
Member
 
Join Date: Dec 2011
Posts: 25
Re: how can i manually connect to WAN through huawei echolife hg532

can anybody please mention the settings for wireless network as it seems like the above user has mentioned settings for the wired one. but still after getting the ID and password everything is fine but still needs settings for wireless. Thanks for the above suggestions.
Reply With Quote
  #9  
Old 30-12-2011
Member
 
Join Date: Jun 2011
Posts: 617
Re: how can i manually connect to WAN through huawei echolife hg532

Quote:
Can anybody please mention the settings for wireless network as it seems like the above user has mentioned settings for the wired one. but still after getting the ID and password everything is fine but still needs settings for wireless. Thanks for the above suggestions.
Yeah why not, see i have mentioned the settings for the wireless connection?so just carry on with this and see whether they are working or not, in my case they are fine.

Similarly as the wired access the router using http://192.168.1.1 and once again you have to click on Basic then Wireless Lan in the menu. Then set the following values as mentioned.

Access Point = Enable
Channel ID = United Kingdom & Select a Channel or Auto
SSID = The name of your network. Any name you like but make a note of it.
Authentication Type = here you have to set the highest level of encryption your equipment can utilize, if possible WPA2, that your equipment will handle.

Pre-Shared Key = Your password make it a mixture on numbers and letters and make a note of it. You will need it and the SSID to connect other wireless devices to your network. And after that once you completed with it just click Submit and it is done.
Reply With Quote
Reply

  TechArena Community > Technology > Networking & Security
Tags: , , , , ,



Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads for: "how can i manually connect to WAN through huawei echolife hg532"
Thread Thread Starter Forum Replies Last Post
How to connect Huawei G7210 phone to PC? Parineeta Portable Devices 5 30-12-2011 02:15 PM
Need help For Huawei EchoLife HG520c Saqlain Networking & Security 3 12-11-2010 04:44 AM
OS 10.5 - need driver for - echolife huawei bm325 Tamila Hardware Peripherals 6 31-07-2010 12:08 AM
Connect HUAWEI ETS1201 FWT modem Cherokee Technology & Internet 5 24-04-2010 01:09 PM
How to manually connect to a wireless network in Windows Vista Faiz_4u Networking & Security 4 23-02-2009 02:35 PM


All times are GMT +5.5. The time now is 09:03 AM.