Go Back   TechArena Community > Technology > Networking & Security
Become a Member!
Forgot your username/password?
Register Tags Active Topics RSS Search Mark Forums Read

Sponsored Links



NETGEAR ProSafe GS105E is not in a similar subnet error

Networking & Security


Reply
 
Thread Tools Search this Thread
  #1  
Old 18-09-2011
Member
 
Join Date: Jun 2011
Posts: 91
NETGEAR ProSafe GS105E is not in a similar subnet error
  

I just acquired a GS105E and ran into a failure actually attempting to gain entrance to the switch. I commissioned the most current form of the prosafe utility. The utility can spot the switch; on the other hand, when I attempt to gain entrance to the switch it hangs a spot and afterward gives me this content "The switch and chief IP location are not in the same subnet!" and denies me promote access. I am on a 192.168.1.xxx subnet but the switch is on a 192.168.0.xxx subnet. Any assistance with this issue could be valued.

Reply With Quote
  #2  
Old 18-09-2011
Member
 
Join Date: Jun 2009
Posts: 1,107
re: NETGEAR ProSafe GS105E is not in a similar subnet error

The utility most unbelievably provides a way to set the IP location of the switch-utilize it to set an IP location in the same subnet as the machine you are utilizing, before trying to gain entrance to the switch. In the farfetched occasion that the utility makes a point not to, set a makeshift static location in the switch's subnet, access the switch and update the IP location as needed.
Reply With Quote
  #3  
Old 18-09-2011
Member
 
Join Date: May 2008
Posts: 945
re: NETGEAR ProSafe GS105E is not in a similar subnet error

The book guarantees that if the switch makes a point not to get a DCHP IP, it defaults to the 0.239 one. Well, I have DHCP and it did not get one so I got the same thing. Just way to get around it is to update your subnet to 192.168.0.* then set a static IP and about-face to your past reach. I did see that the last firmware is 1.0.14 so perhaps that fixes the DHCP issue.
Reply With Quote
  #4  
Old 19-09-2011
Member
 
Join Date: Nov 2009
Posts: 950
re: NETGEAR ProSafe GS105E is not in a similar subnet error

The issue you are having is one of essential network lecturing-and the most effortless course around it is to for a time situated a static on the host you are gaining entrance to the switch from.

"Routing works flawlessly between the switch's and the supervisor's IP, but it declares they are in distinctive networks"-do you hold the few on the same network section or is there as a matter of fact a router between them? In the event that I am in the thick of it is no "tracking" occurring.

The Smart Wizard utilizes show engineering to "come across" the switch and can utilize this same engineering to set an IP location. Contact the manager straightforwardly to the switch and run the wiz.
Reply With Quote
  #5  
Old 19-09-2011
Member
 
Join Date: May 2009
Posts: 1,082
re: NETGEAR ProSafe GS105E is not in a similar subnet error

In the event that you haven't destroyed your mechanism yet attempt checking the taking after:
  1. Check IP of your PC, if your workstation doesn't have an IP location of 192.168.0.x, then you're not in the same subnet as the GS105E
  2. If you have a wireless connector impair it, now and again Windows sets your satellite network as your essential network which can create situations when utilizing the utility.
Reply With Quote
  #6  
Old 19-09-2011
Member
 
Join Date: Jul 2009
Posts: 1,117
re: NETGEAR ProSafe GS105E is not in a similar subnet error

For a consumer product it is a mess of steps to know to get it working. Probably in the destiny, to upgrade the user encounter:
-a manual will swap the A1 poster, or anyhow...
-The .pdf manual could be part of the CD and...
-The default IP could be 192.168.1.239 rather than 192.168.0.239
Reply With Quote
  #7  
Old 19-09-2011
Member
 
Join Date: Jul 2009
Posts: 1,178
re: NETGEAR ProSafe GS105E is not in a similar subnet error

Prosafe isn't consumer side of NETGEAR. Yet, home users (customers) do still buy the products.
Reply With Quote
Reply

  TechArena Community > Technology > Networking & Security
Tags: , , , ,



Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads for: "NETGEAR ProSafe GS105E is not in a similar subnet error"
Thread Thread Starter Forum Replies Last Post
Cannot install Netgear ProSafe VPN client 10.8 on Windows Vista 64 bit Mr.Ryszard Windows Software 6 09-03-2012 02:42 PM
How to get the ProSafe VPN client for netgear Jilesh Networking & Security 4 21-09-2011 11:19 AM
Cannot see NETGEAR ProSafe GS724TV3 in the network Bryant Networking & Security 5 18-09-2011 11:44 PM
Can Netgear GS105E router support Jumbo Frames ? mewlyo Networking & Security 3 15-12-2010 04:07 AM


All times are GMT +5.5. The time now is 12:32 PM.