WRT54GL firmware via tftp import??

[Dewei]

Have a WRT54GL be here and can not die to sign it. ie I can not enter the web interface 192.168.1.1. I have tried several times to the router to be started again. RESET 20 sec. with plug out, etc. What do I know this has Resets the router, perhaps because times short, all LED's on or something. After I had filled the muzzle flash, I just wanted to ne new firmware via TFTP. Ping 192.168.1.1 ran without problems.!! ! At
tftp-i 192.168.1.1 PUT dd-wrt.v24_mini_generic.bin
It brought me after a while the message: Timeout So I really do not go on, because what I do wrong? Please help me.

[yuppicide]

TFTP, you can flash original firmware only. At least if the thing is already half perished. And in your case, you can turn off the option yes no no web interface. The best is, you first flashes on it, the original of which you are doing then load as normal and then on the web interface the dd_v24-generic. I'll hang you turn in the Annex the originals. I think you have the v1.1 right?? Mention your problems in details.

[Dewei]

In the wireless router as I find the "OpenWrt" unsecured network. DAs its far as I know Linux, it may be that I can ping the router only reason not to get the web interface? I've Just tried getting the following message:

C: \> tftp-i 192.168.1.1 PUT: \ dd-c wrt.v24_mini_generic.bin

WinAgents TFTP Client version 1.4 Copyright (c) 2004-2007 by Tandem Systems, Ltd.. - Software for network administrators

Transferring file c: \ dd-wrt.v24_mini_generic.bin to server in octet mode ...
Error occurred during the file transfer (Error code = 0):
Error in recfrom () call. Please check in the TFTP server is available.

Anyone who has any other "3rd party firmware such as DD-WRT is installed, should not" boot-wait switch. In DD-WRT firmware under: administration / management. The "boot-wait" option is turned off and we therefore can not connect. The only question is how to turn on the openwrt firmware this?

[Otto]

How do you reflashing it? If the file is because in C: \??

Then the command is as follows:

tftp-i 192.168.1.1 PUT WRT54GL_4.30.7_code.bin WRT54GL_4.30.7_code.bin

Your command is simply wrong (). 30 sec press reset, wait until the router is pinging, soluble and immediately afterwards the command!!

[Dewei]

Then the command is as follows:
Code:

tftp-i 192.168.1.1 PUT WRT54GL_4.30.7_code.bin WRT54GL_4.30.7_code.bin

Yes I have also done it yet. I have already mentioned that I could ping the router always, that is not my issue.

[Shanbaag]

Yes, what did you do? And what comes to ne news? So far I've only said that you have "C: \> tftp-i 192.168.1.1 PUT c: \ dd-wrt.v24_mini_generic.bin” made. If so, then the command would be:

 C: \> tftp-i 192.168.1.1 PUT dd-wrt.v24_mini_generic.bin wrt.v24_mini_generic.bin dd

[Iker]

C: \> tftp-i 192.168.1.1 PUT dd-dd-wrt.v24_mini_generic.bin

wrt.v24_mini_generic. WinAgents TFTP Client version 1.4 Copyright 2004-2007 by Tandem Systems, Ltd.. http://www.winagents.com - Software for network administrators. Transferring file dd-wrt.v24_mini_generic.bin to server in octet mode ... Error occurred during the file transfer (Error code = 0):

Error in recfrom () call. Please check in the TFTP server is available.

That's funny I can not ping thing dat reach via tftp!!