Go Back   TechArena Community > Hardware > Motherboard Processor & RAM
Become a Member!
Forgot your username/password?
Tags Active Topics RSS Search Mark Forums Read

Reply
 
Thread Tools Search this Thread
  #1  
Old 14-10-2011
Member
 
Join Date: Oct 2011
Posts: 75
Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

I cannot seem to get my ram to speed when I install all 4 sticks in this motherboard. "Kit" for each dual channel works very well in 1066, but the 4 seems to invade the driver or something. Anybody have any knowledge with this? I'm thinking about memory voltage controller or something, nevertheless I'm kind of new-fangled to OCing.
Reply With Quote
  #2  
Old 14-10-2011
Member
 
Join Date: Nov 2010
Posts: 90
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

I will learn some more and observe what I can do on my own. Biostar wants me to RMA the board, but I imagine that is the 'stock answer', and I have no purpose of doing that.
Reply With Quote
  #3  
Old 14-10-2011
Member
 
Join Date: Jul 2011
Posts: 100
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

What happens when the frequency of DRAM> 851MHz. First mix fails, Memtest86 + no, BSODs, etc? Manually change the DDR voltage and four times of primary DRAM (TCL, PRT, and tRAS tRCD) to match the grade SPD / EPP DDR2-1066 data. Also automatically modify the chipset voltage 0.1 - 0.2 V .VNB by evasion in the P45 is 1.1V, so up to 1.2 - 1.3V w / 4 sticks installed.
Reply With Quote
  #4  
Old 14-10-2011
Member
 
Join Date: Jul 2011
Posts: 88
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

An 851MHz everything is fine. Memtest no errors, and Windows 7 Ultimate 64-bit is as happy as a clam (which is where he is now). Car ramps DDR voltage to 2.3V, but 1.1V stays VNB. When I manually to 2.2v DDR, 5-5-5-15 times, VNB to 1.288v (+ 0.2) and set DDR 1066, I have 10,000 in 5 seconds in Memtest. Do not bother to start, for the reason that I'm tired of waiting for the RAID to check / repair. Maybe I should RMA the board?
Reply With Quote
  #5  
Old 14-10-2011
Member
 
Join Date: May 2011
Posts: 468
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

With all the DDR voltage to 2.3 V, and voltage of 0.2 V chipset, change the CAS (TCL), 5-6, and tRAS to 18; 6-5-5-18 (all times in subsection except tRFC Auto, set to 54), then re-run Memtest.
Reply With Quote
  #6  
Old 14-10-2011
Member
 
Join Date: May 2011
Posts: 377
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

Memtest does not even begin to 1066, but I stepped back to 886 and all is well! This is faster than I was able to get!

I think the DDR speed increase is requiring me to reduce some time so the mb can catch up? (Hell, I do not know what I'm saying, just a guess). Do you have any advice when theories that will help me improve on this?
Reply With Quote
  #7  
Old 14-10-2011
Member
 
Join Date: Jun 2011
Posts: 443
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

Code:
ver-Clocking Navigator [Manual OverClock]
Intel(R) SpeedStep(tm) : Disabled
Ratio CMOS Setting : ?6 
CPU Frequency Setting : 570(boot)
Over Clock Retry Count : 2
FSB Compensation: Enabled
FSB(Bsel) To NorthBridge Latch : 1333
DRAM Frequency : DDR2-1140
DDR2 Enhance Mode : Disabled

DRAM Timing Configuration
DDR2 RCOMP Configuration : 2
Static tREAD Value : AUTO
Configure DRAM Timing by SPD : Enabled 

Clock Gen Configuration
PCIE Frequency Setting : 100
CPU Clock Skew Control : 200ps
(G)MCH Clock Skew Control : 100ps
CPU Clock Driving Control : Auto
Reply With Quote
  #8  
Old 14-10-2011
Member
 
Join Date: Jul 2011
Posts: 325
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

I am also having the same trouble. Nevertheless with only two sticks of memory. 1066 windows 7 starts, but hangs during boot correct causing me to reset. And merely work at 851 MHz similar to the OP MOBO. nevertheless with a processor Q6700.What could it be?
Reply With Quote
  #9  
Old 14-10-2011
Member
 
Join Date: Jul 2011
Posts: 455
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

Quote:
Originally Posted by jamiejohn View Post
I am also having the same trouble. Nevertheless with only two sticks of memory. 1066 windows 7 starts, but hangs during boot correct causing me to reset. And merely work at 851 MHz similar to the OP MOBO. nevertheless with a processor Q6700.What could it be?
That would be much better to start your own thread with a full breakdown of your system. Most people do not read all the way through a thread form of age last year to find a new job. Plus it will have all the specifications of your system and CPU-z screenie as mentioned in the posts above. Good luck.
Reply With Quote
  #10  
Old 14-10-2011
Member
 
Join Date: Jul 2011
Posts: 281
Re: Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145

I will as soon as I get home. It bothers me that I cannot use 1066 worth in 1066 .
Reply With Quote
Reply

  TechArena Community > Hardware > Motherboard Processor & RAM
Tags: , , , , , , ,



Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads for: "Cannot set 1066MHZ frequency for Kingston HyperX ddr2 on Biostar Tpower 145"
Thread Thread Starter Forum Replies Last Post
Among Kingston HyperX Blu & HyperX Genesis which one is better Meherr Official Kingston Forum 7 10-06-2013 02:23 PM
kingston DDR3 1066MHZ is not working with the MSI P35 Platinum Combo Stafford Motherboard Processor & RAM 2 19-03-2012 10:37 PM
RAM DDR2 1066Mhz only stable at 800Mhz!! Lalana Motherboard Processor & RAM 3 05-11-2010 02:02 AM
Buy Biostar Tpower i55 jaimins Motherboard Processor & RAM 3 16-11-2009 05:10 PM
Biostar TPower i55 vs Asus Deluxe P7P55D Cisco-s Motherboard Processor & RAM 5 12-11-2009 12:09 PM


All times are GMT +5.5. The time now is 07:18 AM.