Asus mutli-gpu showing up incompatible MSI p55-gd65

[BillieJ]

Sponsored Links

I have comprised a MSI cyclone 460 1024M card. I had purchased an Asus Top 460 1024M card a small number of days ago. Therefore, I wanted to position them in SLI. Additional than my system does not observe the ASUS card. If I position the ASUS card in motherboard unaccompanied, my system determine to observe it and determine to work extremely well. If I position them together (in several slot setup), my system determine to observe merely MSI card. So I have started to give the impression of being for solution. My friend lent me Gigabyte 9600. It runs extremely well through my MSI card, other than I have the similar issue through the asus. Then I tried the asus card by means of gigabyte in dissimilar motherboard MSI X58M and with the purpose of worked. So does anybody be familiar with if my motherboard (MSI p55-gd65) is incompatible through ASUS TOP DirectCU 460 in multi-gpu solution.

[Virtuous]

I anticipate with the purpose of system has to observe mutually of them with and without SLI bridge, for the reason that I be able to utilize one for physX without SLI. In addition, if I have 2 dissimilar cards, system determine to observe them that tested through 9600 and msi 460. Originally I had 259, other than I hoped with the intention of old drivers are my predicament. So I have at present 275.33. I utilized driver sweeper for cleaning old ones for convinced regarding clean installation of drivers. I did not endeavor it. Additional than I will endeavor it, because I have to purchase PSU reduction for one additional 6pin. That PSU did not have encompassed 6pin connectors sufficient for 2x460. However, there was no problem through ASUS and Gigabyte.

[Arjuna3]

Additional than I have that problem by means of my motherboard. If you have encompassed a spare HD, temporary replace the one through OS with it and create a temporary install of windows, do not activate it, install the asus the driver, the msi and the driver . So similar to that, most of them gone exclude a corruption of your actual Windows.

[Gajanand]

I had installed the system the entire in excess off again and the issue is tranquil there. My systems still observe merely one graphic card. Therefore, it is not problem of the system. I did not have chance to purchase reduction.

[fragranz]

However, the asus card does not run even through 9600 in my motherboard. Or give me if there is not much detail or the image links do not run, received the h50-1, the one through the 1156 well-matched bracket, this morning for my i5 750 mounted on an MSI p55 gd65. The predicament is through the screws that hold down the mosfet heatsinks approximately the cpu socket. The top right screwhead when give the impression of being at the back of the motherboard is fouled by the bracket. As a consequence, the bracket does not sit level to the motherboard on this corner, probably resulting in uneven cpu to cooler contact, if there is sufficient screw thread to create it to the bracket.

[Jabeena]

I might just trim with the intention of a diminutive bit through a dremel tool or a razor knife. It does not give the impression of being similar to you necessitate to take that much off. You desire it laying flat. I got the similar motherboard and have the similar predicament, I am receiving ready to just utilize a dremel on the plastic bracket, be supposed to not take much to create it flush with the mobo.

[Udyan]

They did not be familiar with that MSI decided to be a retard and position a screw in with the intention of corner. I managed to acquire mine in without cutting/hacking/grinding it. Additional than subsequent to looking at it, A diminutive grinding in with the intention of corner might create it fit additional snugly. I might do that in the next a small number of days. If you have to bench grinder, it might in addition work. Just presently hold on to the big part of the bracket and take your time.

[Pomegranate]

You be supposed to not be building your own systems if a diminutive modification similar to this might acquire you frustrated. It’s regarding a 10 second fix. And you not be able to blame MSI or corsair for the reason that Corsair by no means even seen this motherboard when they completed the mounts in view of the fact that its merely similar to a week old. There is not much to take off so is not much of a problem. If you do not have a dremel similar to me acquire a sharp knife such as a scalpel, stanley knife/carpet blade. If you encompass something similar to sharp pliers, I imagine they might be called tinsnips or perhaps even dedicated wire cutters (not sure); you be able to utilize these to nip away at a segment of plastic which eliminates the bulk of the waste. Then you be able to just presently take the knife and slice alongside the groove you have just completed, to round it out. Merely took a small number of seconds as there was hardly no matter which that had to come out, maybe regarding 2mm of plastic at the deepest point.